• .

  • 5

    Majestic 15W-50 Synthetic Blend super Heavy-Duty Diesel Engine Oil, API CJ-4/SM

    COMPOSITION/ INFORMATION ON INGREDIENTS

    COMPONENTS CAS # AMOUNT
    Non-Hazardous Additive Blend in Severely Hydrotreated Synthetic and Paraffinic Oil Mixture 100%weight

    HAZARDS IDENTIFICATION

    IMMEDIATE HEALTH EFFECTS
    Eye: Not expected to cause prolonged or significant eye irritation.

    Skin: Contact with the skin is not expected to cause prolonged or significant irritation. Not expected to be harmful to internal organs if absorbed through the skin. High-Pressure Equipment Information: Accidental high-velocity injection under the skin of materials of this type may result in serious injury. Seek medical attention at once should an accident like this occur. The initial wound at the injection site may not appear to be serious at first; but, if left untreated, could result in disfigurement or amputation of the affected part.

    Ingestion: Not expected to be harmful if swallowed. Inhalation: Not expected to be harmful if inhaled. Contains a petroleum-based mineral oil. May cause respiratory irritation or other pulmonary effects following prolonged or repeated inhalation of oil mist at airborne levels above the recommended mineral oil mist exposure limit. Symptoms of respiratory irritation may include coughing and difficulty breathing.

    FIRST AID MEASURES

    Eye: No specific first aid measures are required. As a precaution, remove contact lenses, if worn, and flush eyes with water.

    Skin: No specific first aid measures are required. As a precaution, remove clothing and shoes if contaminated. To remove the material from skin, use soap and water. Discard contaminated clothing and shoes or thoroughly clean before reuse.

    Ingestion: No specific first aid measures are required. Do not induce vomiting. As a precaution, get medical advice.

    Inhalation:No specific first aid measures are required. If exposed to excessive levels of material in the air, move the exposed person to fresh air. Get medical attention if coughing or respiratory discomfort occurs.

    Note to Physicians: In an accident involving high-pressure equipment, this product may be injected under the skin. Such an accident may result in a small, sometimes bloodless, puncture wound. However, because of its driving force, material injected into a fingertip can be deposited into the palm of the hand. Within 24 hours, there is usually a great deal of swelling, discoloration, and intense throbbing pain. Immediate treatment at a surgical emergency center is recommended.

    FIRE FIGHTING MEASURES

    Leaks/ruptures in high pressure system using materials of this type can create a fire hazard when in the vicinity of ignition sources (eg. open flame, pilot lights, sparks, or electric arcs).

    FIRE CLASSIFICATION: OSHA Classification (29 CFR 1910.1200): Not classified by OSHA as flammable or combustible.

    NFPA RATINGS: Health: O Flammability: 1 Reactivity: O

    FLAMMABLE PROPERTIES:
    Flashpoint: (Cleveland Open Cup) 195 0C (385 0F) (Min)
    Autoignition: No Data Available
    Flammability (Explosive) Limits (0/0 by volume in air): Lower: Not Applicable Upper: Not Applicable

    EXTINGUISHING MEDIA: Use water fog, foam, dry chemical or carbon dioxide (C02) to extinguish flames.

    PROTECTION OF FIRE FIGHTERS:
    Fire Fighting Instructions: This material will burn although it is not easily ignited. For fires involving this material, do not enter any enclosed or confined fire space without proper protective equipment, including self-contained breathing apparatus.

    Combustion Products: Highly dependent on combustion conditions. A complex mixture of airborne solids, liquids, and gases including carbon monoxide, carbon dioxide, and unidentified organic compounds will be evolved when this material undergoes combustion.

    ACCIDENTAL RELEASE MEASURES

    Protective Measures: Eliminate all sources of ignition in vicinity of spilled material.

    Spill Management: Stop the source of the release if you can do it without risk. Contain release to prevent further contamination of soil, surface water or groundwater. Clean up spill as soon as possible, observing precautions in Exposure Controls/Personal Protection. Use appropriate techniques such as applying noncombustible absorbent materials or pumping. Where feasible and appropriate, remove contaminated soil. Place contaminated materials in disposable containers and dispose of in a manner consistent with applicable regulations.

    Reporting: Report spills to local authorities and/or the U.S. Coast Guard’s National Response Center at (800) 424-8802 as appropriate or required.

    HANDLING AND STORAGE

    Precautionary Measures: DO NOT USE IN HIGH PRESSURE SYSTEMS in the vicinity of flames, sparks and hot surfaces. Use only in well ventilated areas. Keep container closed.

    General Handling Information: Avoid contaminating soil or releasing this material into sewage and drainage systems and bodies of water.

    Static Hazard: Electrostatic charge may accumulate and create a hazardous condition when handling this material. To minimize this hazard, bonding and grounding may be necessary but may not, by themselves, be sufficient. Review all operations which have the potential of generating and accumulating an electrostatic charge and/or a flammable atmosphere (including tank and container filling, splash filling, tank cleaning, sampling, gauging, switch loading, filtering, mixing, agitation, and vacuum truck operations) and use appropriate mitigating procedures. For more information, refer to OSHA Standard 29 CFR 1910.106, ‘Flammable and Combustible Liquids’, National Fire Protection Association (NFPA 77, ‘Recommended Practice on Static Electricity’, and/or the American Petroleum Institute (API) Recommended Practice 2003, ‘Protection Against Ignitions Arising Out of Static, Lightning, and Stray Currents’.

    Container Warnings: Container is not designed to contain pressure. Do not use pressure to empty container or it may rupture with explosive force. Empty containers retain product residue (solid, liquid, and/or vapor) and can be dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricity, or other sources of ignition. They may explode and cause injury or death. Empty containers should be completely drained, properly closed, and promptly returned to a drum reconditioner or disposed of properly.

    EXPOSURE CONTROLS/PERSONAL PROTECTION

    GENERAL CONSIDERATIONS: Consider the potential hazards of this material (see Section 3), applicable exposure limits, job activities, and other substances in the work place when designing engineering controls and selecting personal protective equipment. If engineering controls or work practices are not adequate to prevent exposure to harmful levels of this material, the personal protective equipment listed below is recommended. The user should read and understand all instructions and limitations supplied with the equipment since protection is usually provided for a limited time or under certain circumstances.

    ENGINEERING CONTROLS: Use in a well-ventilated area.

    PERSONAL PROTECTIVE EQUIPMENT
    Eye/Face Protection: No special eye protection is normally required. Where splashing is possible, wear safety glasses with side shields as a good safety practice.

    Skin Protection: No special protective clothing is normally required. Where splashing is possible, select protective clothing depending on operations conducted, physical requirements and other substances in the workplace. Suggested materials for protective gloves include: 41-1 (PE/EVAL), Nitrile Rubber, Silver Shield, Viton.

    Respiratory Protection: No respiratory protection is normally required. If user operations generate an oil mist, determine if airborne concentrations are below the occupational exposure limit for mineral oil mist. If not, wear an approved respirator that provides adequate protection from the measured concentrations of this material. For air-purifying respirators use a particulate cartridge. Use a positive pressure air-supplying respirator in circumstances where air-purifying respirators may not provide adequate protection.

    Occupational Exposure Limits:

    Component Agency TWA STEL CEILING NOTATION
    Non Hazardous Additive Blend in Refined Oil ACGIH 5 mg/m3 10 mg/m3
    Non Hazardous Additive Blend in Refined Oil OSHA Z-1

    PHYSICAL AND CHEMICAL PROPERTIES

    Attention: the data below are typical values and do not constitute a specification.

    Color: Yellow to Amber Liquid Odor: Petroleum odor pH: Not Applicable
    Vapor Pressure: <0.01 mmHg @ 37.8 0C(100 0F)
    Vapor Density (Air = 1): >1
    Boiling Point: >315.6 0C (600 0F)
    Solubility: Soluble in hydrocarbon solvents; insoluble in water.
    Freezing Point: Not Applicable
    Melting Point: Not Applicable
    Specific Gravity: 0.86 – 0.9 @ 15.6 0C (60.1 0F) / 15.6 0C (60.1 0F)
    Density: 0.86 kg/’ – 0.9 kg/’ @ 15 0C (59 0F) Viscosity: 18.3-21.9 cSt @ 100 0C

    STABILITY AND REACTIVITY

    Chemical Stability: This material is considered stable under normal ambient and anticipated storage and handling conditions of temperature and pressure.

    Incompatibility With Other Materials: May react with strong acids or strong oxidizing agents, such as chlorates, nitrates, peroxides, etc.

    Hazardous Decomposition Products: None known (None expected) Hazardous Polymerization: Hazardous polymerization will not occur.

    TOXICOLOGICAL INFORMATION

    IMMEDIATE HEALTH EFFECTS
    Eye Irritation: The eye irritation hazard is based on evaluation of data for similar materials or product components. Skin Irritation: The skin irritation hazard is based on evaluation of data for similar materials or product components.
    Skin Sensitization: No product toxicology data available.

    Acute Dermal Toxicity: The acute dermal toxicity hazard is based on evaluation of data for similar materials or product components.

    Acute Oral Toxicity: The acute oral toxicity hazard is based on evaluation of data for similar materials or product components.

    Acute Inhalation Toxicity: The acute inhalation toxicity hazard is based on evaluation of data for similar materials or product components.

    ADDITIONAL TOXICOLOGY INFORMATION: This product contains petroleum base oils which may be refined by various processes including severe solvent extraction, severe hydrocracking, or severe hydrotreating. None of the oils requires a cancer warning under the OSHA Hazard Communication Standard (29 CFR 1910.1200). These oils have not been listed in the National Toxicology Program (NTP) Annual Report nor have they been classified by the International Agency for Research on Cancer (IARC) as; carcinogenic to humans (Group 1 probably carcinogenic to humans (Group 2A), or possibly carcinogenic to humans (Group 2B). These oils have not been classified by the American Conference of Governmental Industrial Hygienists (ACGIH) as: confirmed human carcinogen (Al), suspected human carcinogen (A2), or confirmed animal carcinogen with unknown relevance to humans (A3).

    ECOLOGICAL INFORMATION

    ECOTOXICITY 96 hour(s) LC50: >1000 mg/l (Oncorhynchus mykiss) 48 hour(s) ECO: >1000 mg/l (Daphnia magna) This material is not expected to be harmful to aquatic organisms.

    ENVIRONMENTAL FATE This material is not expected to be readily biodegradable.

    DISPOSAL CONSIDERATIONS

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. Contact your sales representative or local environmental or health authorities for approved disposal or recycling methods.

    TRANSPORT INFORMATION

    The description shown may not apply to all shipping situations. Consult 49CFR, or appropriate Dangerous Goods Regulations, for additional description requirements (e.g., technical name) and mode-specific or quantity-specific shipping requirements.

    DOT Shipping Description: PETROLEUM LUBRICATING OIL
    IMO/IMDG Shipping Description: PETROLEUM LUBRICATING OIL

    REGULATORY INFORMATION

    EPCRA 311/312 CATEGORIES:
    1. Immediate (Acute) Health Effects: NO
    2. Delayed (Chronic) Health Effects: NO
    3. Fire Hazard: NO
    4. Sudden Release of Pressure Hazard: NO
    5. Reactivity Hazard: NO

    REGULATORY LISTS SEARCHED:

    01-1=IARC Group 1 03=EPCRA 313
    01-2A=IARC Group 2A 04=CA Proposition 65
    01-2B=IARC Group 2B 05=MA RTK
    02=NTP Carcinogen 06=NJ RTK
    07=PA RTK

    No components of this material were found on the regulatory lists above.

    CHEMICAL INVENTORIES: All components comply with the following chemical inventory requirements: AICS (Australia), EINECS (European Union), ENCS (Japan), KECI (Korea), PICCS (Philippines), TSCA (United States).

    One or more components does not comply with the following chemical inventory requirements: DSL (Canada).

    NEW JERSEY RTK CLASSIFICATION: Under the New Jersey Right-to-Know Act L. 1983 Chapter 315 N.J.S.A. 34:5A-1 et. seq., the product is to be identified as follows: PETROLEUM OIL (Hydraulic oil)

    WHMIS CLASSIFICATION: This product is not considered a controlled product according to the criteria of the Canadian Controlled Products Regulations.

    OTHER INFORMATION

    NFPA RATINGS: Health: 0 Flammability: 1 Reactivity: 0

    HMIS RATINGS: Health: 1 Flammability: 1 Reactivity: 0 (0-Least, I-Slight, 2-Moderate, 3-High, 4-Extreme, PPE:- Personal Protection Equipment Index recommendation, *- Chronic Effect Indicator). These values are obtained using the guidelines or published evaluations prepared by the National Fire Protection Association (NFPA) or the National Paint and Coating Association (for HMIS ratings).

    ABBREVIATIONS THAT MAY HAVE BEEN USED IN THIS DOCUMENT:
    TLV – Threshold Limit Value
    TWA – Time Weighted Average
    STEL – Short-term Exposure Limit
    PEL – Permissible Exposure Limit
    CAS – Chemical Abstract Service Number
    ACGIH – American Conference of Government Industrial Hygienists
    IMO/IMDG – International Maritime Dangerous Goods Code
    API – American Petroleum Institute
    MSDS – Material Safety Data Sheet
    NFPA – National Fire Protection Association (USA) DOT – Department of Transportation (USA)
    NTP – National Toxicology Program (USA)
    IARC – International Agency for Research on Cancer
    OSHA – Occupational Safety and Health Administration

    The above information is based on the data of which we are aware and is believed to be correct as of the date hereof. Since this information may be applied under conditions beyond our control and with which we may be unfamiliar and since data made available subsequent to the date hereof may suggest modifications of the information, we do not assume any responsibility for the results of its use. This information is furnished upon condition that the person receiving it shall make his own determination of the suitability of the material for his particular purpose.